How to patch a concrete slab floor that has cracked and slopes 3" in 10 feet? - patch do clonk rage
The ground breaking hovers above the ground and walls, which will show no signs of movement, but the stone through the middle part and the other half is now with a slope of about 3 "10 '. This happened several years and there was no signs of deterioration over the past two years. How can I patch the call for a return to a status? "Now you have an old vinyl tiles or asphalt if the Level I refloor with tile and laminate. Should we remove the old tiles before patches? Is there a kind of self leveling cement that I use, or something that is strong enough to spring a fine point? Of course, I fear, without knowing the cause of colonization, but you do not know how research is understood the board. Any ideas or suggestions are welcome.
Wednesday, February 3, 2010
Patch Do Clonk Rage How To Patch A Concrete Slab Floor That Has Cracked And Slopes 3" In 10 Feet?
Subscribe to:
Post Comments (Atom)
4 comments:
The soil has failed, because the earth and stone beneath the plate thoroughly compacted and / or plaque is not properly paid. I think it is a slab on the floor? In your living room or what? The best way is this kind of table is as follows: Suppose that the foundation (or concrete is poured into a mold, or whether they are built with cement blocks) 8 cm deep. The upper block would be only 6 inches deep. The difference is about 2 inches on the inside circumference of the base to form a frame around it. The concrete slab would be poured over the gravel about 2 cm below the rim of the one already described. If you then pour the concrete (usually 4 cm deep), will inch up and over the edge about 2. So we end up with the record have a kind of tire that sits on the edge of 2 inches, not to the bottom of the earth, if you scroll down. Floating plates were popular with the manufacturers, there are about 20 years ago in an attempt to prevent cracks cellars. Cracking tends to occur over time, theon a slab was poured on the ground by sedimentation, water, plates, etc floating in my experience are nothing but trouble. You can slide into the water and bugs, etc. You can of cement poured on the existing tiles, but was postponed because the plate, one step back. So your solution may be only temporary. But now you can try to simply make a new layer of concrete on top. Get up cement slab and use only ordinary Portland cement poured on him.
The soil has failed, because the earth and stone beneath the plate thoroughly compacted and / or plaque is not properly paid. I think it is a slab on the floor? In your living room or what? The best way is this kind of table is as follows: Suppose that the foundation (or concrete is poured into a mold, or whether they are built with cement blocks) 8 cm deep. The upper block would be only 6 inches deep. The difference is about 2 inches on the inside circumference of the base to form a frame around it. The concrete slab would be poured over the gravel about 2 cm below the rim of the one already described. If you then pour the concrete (usually 4 cm deep), will inch up and over the edge about 2. So we end up with the record have a kind of tire that sits on the edge of 2 inches, not to the bottom of the earth, if you scroll down. Floating plates were popular with the manufacturers, there are about 20 years ago in an attempt to prevent cracks cellars. Cracking tends to occur over time, theon a slab was poured on the ground by sedimentation, water, plates, etc floating in my experience are nothing but trouble. You can slide into the water and bugs, etc. You can of cement poured on the existing tiles, but was postponed because the plate, one step back. So your solution may be only temporary. But now you can try to simply make a new layer of concrete on top. Get up cement slab and use only ordinary Portland cement poured on him.
I think there are a number of problems.
1. Water intrusion has caused govern the earth under the concrete. Patch is not the answer
2. Inadequate gravel base under the plate. Patches not yet found a solution
You will probably to call someone, or a budget. Ussually get estimates are free and can learn a lot from you. Core or a hole in the middle of the Depression, to see what is in the concrete. In any case, you will probably remove all the concrete and fix the problem before pouring more concrete. Adding more concrete the problem is not solved, which is a great depression.
I agree with the answers in a way that the material is deleted / moved, causing a void beneath the plate, it seems that the thickness of the plate is all that little or reinforcing bars in (if necessary) - since theres no support for the concrete, weakening and cracking. The ability to cut a few holes in the concrete floor and inspect the damage - whatever is possible to close the gap with the specific bridge could, I would beg you to an engineer Tho. The more fundamental question is condensation or addition of further support or then top with concrete permently to assess the situation properly filled. I think the best way to solve the break completely to the ground and laid the foundation / concrete - both options are not religious.
Post a Comment